Start XCTU. It will start on “PC Settings” loss. On the website, pick your XBee Explorer’s COM slot and make sure the port settings tend to be as below (9600 8-N-1). Very first, create your COM interface and make certain the settings become proper.
Strike Test/Query to ensure that you can keep in touch with your XBee Wi-fi. You ought to get a reply like: This is a good sign! Means we are communicating with the XBee.
Mouse click to the “Modem setup” loss. And click “Review” to display your XBee Wi-fi’s retained options. A view from the XBee WiFi’s standard variables.
Select “energetic Scan” nearby the the surface of the scrolling window. Subsequently click the “Scan” button** that looks. This will start the network scan utility.
Click on the “Scan” switch at the end in the scan screen. If all goes really, the community should show up above. The “back link Margin” appreciate presents the strength of the signal (larger is better). And also the “protection” importance indicates the encoding function on the circle. Pick the system’s SSID, submit a passkey if necessary, and then click “Select AP”.
Pick your network. If it’s encoded, enter your protection trick. Next click “pick AP” (perhaps not “finished”!). XCTU will arrange your own XBee, and it’ll try lease a DHCP address in the event your network is initiated for it.
After effectively connecting, click “browse” on top of the windows once again. This may revise every one of the XBee’s options, like GW (the gateway IP), MK (the subnet mask), and the (the component’s designated IP). If these principles all make sense, next congratulations, the XBee is connected with their WiFi network! Our XBee WiFi module’s ip is actually 192.168.0.101.
Yay! What now? There are some information you’ll go:
If you’ve ever made use of XBees earlier, it is likely you think about them as easy-to-setup cordless transceivers. Two XBees, set up precisely, can seamlessly pass facts to each other from a single serial port to a different. XBee Wi-fi’s are not any different!
After that exact same collection of measures, you are able to set-up another XBee WiFi component to additionally connect with your cordless network. It will have an original IP address (usually assigned via DHCP). Observe that.
To create two XBees to communicate to one another, you will need to modify the DL — Destination ip — of each and every to the other XBee. Possible opened another XCTU windows, or configure every one at any given time.
You’ll be able to hit over to the Terminal tab to type characters and get them sent out of your desktop, through one XBee, inside different XBee and out over another terminal.
Another elective software of these modules is by using them about cloud. Digi’s product Cloud provider renders this very easy. Mouse click over to another web page observe an example set-up.
XBee WiFi’s are made to allow quick communication with unit Cloud by Etherios (TM). The unit affect provider allows you to interface the XBee Wi-fi using web, where you can get a handle on the I/O pins and study its reputation from comfy boundaries of one’s browser (anywhere in the world!).
Now, equipment Cloud try a made service, but it is pretty not too expensive (right down to $0.50 per tool monthly). Additionally they create a totally free 30 day trial any time you simply want to give it a shot, which will be what we’ll perform right here.
Here you can view and manage just about everything because pertains to the XBee. You can put pins movement and value inside insight and result options loss. Decide to try establishing a pin to “result High”, subsequently click salvage . The pins must have started driven to 3.3V, but exactly how did you know? Time for you whip a circuit collectively!
Discover the circuit we are going to used to obtain the most of XBee’s example affect dash. It’s not necessary to get together all, but we advice about trying the LED attached to pin 13.
You will however want to drive the XBee Wi-fi component. It would possibly stay static in the XBee Explorer, or you can plug it into another XBee Breakout panel. Here is a graphic of our own hookup using:
Now that we have now affixed some buttons and LEDs, it is time to go on it into affect!
Experiment along with it! Test turning the Light-emitting Diode on remotely. Subsequently review some keys and potentiometers. Very cool! Today inquire a pal from over the sea to get it done. Actually cool!
If you’d like to create out your very own application, all the necessary rule is actually viewable by pressing the option on a widget. It seems like everything’s managed on Digi’s GitHub page, which we’re big fans of.
Now you’ve taken your XBee to the affect, exactly what awesome Internet-of-Things app will you making? If you want any services, or this tutorial didn’t respond to all of your current matter, consider looking at these budget aswell: